Home / Analytes / Ipamorelin
Ipamorelin
What identity means for this molecule in numbers, how we measure its purity, and whether that method is validated yet. CAS 170851-70-4 Not yet checked against the CAS registry.
Identity by mass spectrometry
Identity by LC–MS means every charge state we record lands within 10 parts per million of where the formula says it must. That establishes the formula of the main component; the limits page says what it does not establish. The windows below are that criterion in daltons, at each m/z.
Molecular formula
C38H49N9O5
Monoisotopic mass
711.3857 Da, free peptide
Average mass
711.85 Da, free peptide
| State | m/z | 10 ppm, Da | 10 ppm, mDa | Isotope spacing, m/z |
|---|---|---|---|---|
| [M+H]+ | 712.3929 | ±0.0071 | ±7.1 | 1.003 |
| [M+2H]2+ | 356.7001 | ±0.0036 | ±3.6 | 0.501 |
Scan range 300–2200. The bold state is the one expected to be most abundant. We expect the envelope to centre on the smaller of M/1000 + 1 and the larger of the basic-site count and M/1000, M in daltons; here that is M/1000 + 1 = 1.7. It has 3 basic sites, and a peptide this size rarely carries more charges than that. Two states fall inside the range, and identity rests on both agreeing within 10 ppm.
The last column is the spacing between neighbouring isotope peaks of each ion: the mean step one heavy isotope adds to this composition, 1.0029 Da, divided by the charge. The higher the charge, the closer the peaks; at [M+2H]2+ they sit 0.501 m/z apart, one part in 710 of its m/z. Resolving power is m/z over the smallest separation an instrument shows, so the method’s floor of 10 000 at m/z 1000 shows peaks 0.1 m/z apart there, against 0.20 m/z between the isotope peaks of a 5+ ion at that m/z: that is why the 10 ppm criterion is applied only on an instrument of that resolving power or better, and why a unit-resolution instrument, which shows peaks about 1 m/z apart, cannot pick the monoisotopic peak out of any cluster past 1+.
What the mass cannot see. This peptide differs from an isomer of identical mass only in the configuration of the 2-naphthylalanine and the phenylalanine at positions 3 and 4, both D (any epimer of either, and the 1-naphthyl positional isomer, has the same formula). Mass spectrometry cannot see that difference; with Purity, the retention time of the main peak against our reference standard, printed with the system suitability, is the only evidence the report offers for it, and an identity-only report has none.
Method and validation status
Purity is area percent by RP-HPLC–UV 214 nm. Identity is LC–MS (ESI+). The matrix we accept is lyophilised powder.
Status
- Validation
- Not yet validated
- Retention time
- not yet measured on this analyte
- Limit of quantitation
- not yet measured
- Reporting threshold
- 0.05% area; no limit of quantitation is claimed yet, so a smaller peak may be present and not seen
Not yet validated means the method is written and has not been run on this analyte. The retention time and the limit of quantitation are listed once measured, with the date of the validation that produced them. The scope table shows the status of every analyte.
What the formula tells us to watch for
- Deamidation does not apply: the sequence has no asparagine or glutamine.
- Truncation products - the sequence short by one or more residues - fall at characteristic mass offsets and are looked for at their expected m/z where the sequence is on file; the certificate lists the impurity masses that were read and whether each was assigned.
Order a test of Ipamorelin
Identity and purity together, $185, in 10 business days or the invoice is cancelled, or the payment refunded, and you still get the results. One sealed container as received.
What you get back
A certificate with the chromatogram, every peak, the three injections, the measured spectrum against the windows above, what could not be resolved, a full signature, a hash and a QR that verifies without us. How to read one.